Planet Technology WAP-1963 Manual do Utilizador

Wireless Access Point WAP-1963 User’s Manual

6 3.1.2 Wireless Setting: In this option, you can set the Mode, Alias Name, ESSID and Work Channel to this Access Point. When configuration finish

7 Channel 1-13 (Europe) Associated Clients Click “Show Active Clients” button, then a “Active Wireless Client Table” will pop up as below. You can se

8 3.1.2.2 STATION-AD HOC MODE Served as a wireless station (Ad-hoc). Connected to a PC or a small LAN, this station along with other wireless stati

9 Parameters Description Alias Name The alias name of this access point. ESSID The ESSID (up to 31 printable ASCII characters) is the unique name

10 3.1.3 Wireless Advance Settings: You can set advanced parameters of this WAP-1963. The parameters include Authentication Type, Fragment Threshol

11 RTS Threshold When the packet size is smaller the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet. Beacon

12 3.1.4 Security: WEP is an authentication algorithm, which protects authorized Wireless LAN users against eavesdropping. The Authentication type

13 text box by following the rules below. 64-bit WEP: input 10-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or 5-digit ASCII character as

14 3.1.5 MAC Filtering: This Access Point provides MAC Address Filtering, which prevents the unauthorized MAC Addresses from accessing your wireles

15 All” button. Reset Click “Reset” will clear your current selections.

2 Copyright Copyright  2003 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribe

16 3.1.6 System Utility: From here, you can define the Access Point’s IP Address and Login Password and enable the Access Point to be a DHCP Server

17 Re-Enter Password Reconfirm the password (up to 15-digit alphanumeric string) you want to login to the Access Point. Note that the password is cas

18 3.1.7 Configuration Tool The Configuration Tool screen allows you to backup, restore and reset WAP-1963 configuration settings. Saving the config

19 3.1.8 Upgrade This page allows you to upgrade WAP-1963 with when the new firmware released. Parameter Description Firmware Upgrade You can use

20 3.1.9 Reset You can reset the Access Point’s system should any problem exist. The reset function essentially Re-boots your Access Point’s system.

21 Chapter 4 Application This chapter describe the four operating mode of your WAP-1963. The four working modes of WAP-1963 are Access Point, Access

Chapter 5 Troubleshooting This chapter gives tips on how to configure the communication software. This chapter provides solutions to problems usually

23 Q. What is Roaming? A. Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area grea

3 interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Stat

4 TABLE OF CONTENTS Chapter 1 Introduction 1 1.1 Package Contents 1 1.2 System Requirements 1 1.3 Features 1 1.4 Specification 2 Chapter 2 Har

1 Chapter 1 Introduction Thank you for purchasing WAP-1963. This device is an access point for IEEE 802.11b 2.4GHz wireless network. You can use thi

2 • Seamlessly integrate wireless and wired Ethernet LAN networks • Interferences Provide 64/128-bit WEP Encryption and MAC Filter to protect the wi

3 Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-1963. 2.

4 Chapter 3 Configuration 3.1 Configure through Web Browser Web configuration provides a user-friendly graphical user interface (web pages) to manag

5 3.1.1 Home: On this screen, you can see the general information of the Access Point including Alias Name, Firmware Version, SSID, Channel Number,