Planet Technology WAP-4030A Manual do Utilizador

54Mbps Wireless Access Point w/bridge, inter-building WAP-4030A User’s Manual

3.1.1 Client Mode In this screen, you can configure WAP-4030A as a wireless client. It is used to let a network device with only wired Ethernet func

Parameter Description Station Mode 802.11b: It allows to select the transmit rate up to 11Mbps. Mixed: It allows to select the transmit rate up to 5

Infrastructure: It can let your network device join a wireless LAN through an access point. Channel Select the appropriate channel from the list pro

Parameter Description Mode 802.11b mode: It allows to select the transmit rate up to 11Mbps 802.11g mode: It allows to select the transmit rate up

securely. You may refer to section 3.5 to know the detail settings of it. WPA: You can use a pre-shared key to authenticate wireless stations and en

and multicast messages. Protection Mode It provides best performance for 11g transmission when you enable it. Transmit Rate When you enable the st

3.1.2.2 Access Filter This Access Point allows you to provide a Filter List of MAC addresses that are allowed/denied associating with this AP. Parame

3.1.3 Repeater Mode In this mode, WAP-4030A can be a repeater between Access Point and wireless clients, that can extend the connect distance of your

be 50% as the clients connect to AP directly. When clients connect to second WDS Repeater, the performance will be 25%. Universal Repeater: This repea

access point easily. If you are building a public wireless network, enabling this feature is recommended. Disabling "Response to Broadcast ESSID

Copyright Copyright © 2005 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, s

Parameter Description AP MAC Address You have to enter the MAC addresses of another WAP-4030A that it will connect to.Mode 802.11b mode: It allows

3.1.4.1 Advance Setting Parameter Description RTS Threshold When the packet size is smaller the RTS threshold, the access point will not use the

3.1.5 Point-to-Multipoint Mode This function provides to bridge more than 2 wired Ethernet networks together by wireless connection. You can use more

3.1.4.1 to configure. Please click “Apply” button to save the above configurations. 3.2 Status In this option, you can see the WAP-4030A current s

Parameter Description FW Version It shows the current firmware version. FW Upgrade This tool allows you to upgrade WAP-4030A firmware. Before upgr

Parameter Description Device Name It shows current device name. Automatic IP If there is a DHCP Server in your LAN, you can select this option to

3.5 WEP Parameter Description WEP Length WEP-64: input 10-digit Hex values or 5-digit ASCII character as the encryption keys. WEP-128: input 26-digi

3.6 WPA-PSK Parameter Description Authentication Type The Pre-shared key is used to authenticate and encrypt data transmitted in the wireless netwo

Chapter 4 Troubleshooting This chapter provides answer to problems usually encountered during the installation and operation of the Wireless Network A

interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Stateme

TABLE OF CONTENTS Chapter 1 Introduction ...5 1.1 Package Contents..

Chapter 1 Introduction Thank you for purchasing WAP-4030A. The WAP-4030A supports both IEEE 802.11b and IEEE 802.11g standards. You can use it to con

 Provide WPA-PSK, 64/128-bit WEP Encryption and MAC Filter to protect the wireless data transmissions  Support Wireless AP / Client / Repeater and

LED Indicators 3; PWR, WLAN, LAN Power 12V DC, 1A Temperature 0 ~ 55°C (Operating) Humidity 10 ~ 90%, non-condensing (Operating) Dimension 169 x 8

Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-4030A. 2.1 H

Chapter 3 Configuring the Wireless AP Web configuration provides a user-friendly graphical user interface (web pages) to manage your WAP-4030A. An AP